產品展示PRODUCTS
混凝土抗?jié)B儀/混凝土抗?jié)B儀操作規程
更新時間:2023-09-04
訪問量:1915
廠商性質:生產廠家
生產地址:
混凝土抗?jié)B儀/混凝土抗?jié)B儀操作規程/自動調壓混凝土抗?jié)B儀
HP-4.0混凝土抗?jié)B儀
一、適用范圍
混凝土、是現在建筑中被廣泛使用的人工石材,對于某些建筑,如水工建筑、水下、水中、地下和其他建筑工程,要求建筑物具有特殊的性能-抗?jié)B性能所謂抗?jié)B性能是指構筑物所使用的材料能抵抗水和或其他液體(輕油、重油)介質在壓力作用下滲透的性能。
HP-4.0型抗?jié)B儀主要使用于湖擰土抗?jié)B性能和是試驗和抗?jié)B標號的測定。同時也可利用它做建筑材料透氣性的測定和質量檢查,因此得到了有關生產、施工、設計、教研等部門的廣泛使用。
二、主要技術參數
1、zui大工作壓力:4mpa
2、工作方式:自動恒壓(數顯型:自動恒壓且自動升壓)
3、一次可作試件數:6個
4、試模幾何尺寸(亦稱主模)
模腔上口直徑:φ174.8mm
模腔下口直徑:φ185mm
高度:153mm
5、柱塞泵參數:
流量:0.16L/min
6、電動機:
功率:120W
電源:380V-50HZ
7、外形尺寸:950×800×950mm
8、質量:≈220kg
三、主要工作原理及其機構(見附圖一)
HP-4.0型抗?jié)B儀是利用密封容器內壓力處處相等的原理(水位差疏忽不計),以水泵對整個系統輸壓,并通過電接點壓力表或壓力控制器加壓壓力的大小來實現壓力水由下向上滲透壓裝在試模中的試件,從而測定試件抗?jié)B性能和計算其抗?jié)B標號的儀器。HP-4.0型砼抗?jié)B儀主要由箱體、工作臺,由不銹鋼面板制成,并安裝有6個模座及36個M12螺栓,用于安裝試模之用。
供壓系統,由電動機、動力箱、水泵、水包、安全閥,管道等組成,電動機用于向系統提供動力源,動力箱用于將電動機所提供的動力源轉化成往返運動的動力并提供給水泵,水泵用以向整個系統提供水壓,水包用以穩定供應系統的水壓,并起水壓源,動力箱用于將電動機所提供的動力源轉化成往返運動的動力并提供給水壓,并起水壓源的分流作用;安全閥安裝字水包中央,安全閥的作用是確保系統壓力不大于4MPA4、操作臺,主要由電器控制和控制閥組成。
HP-4.0型砼抗?jié)B儀電器控制部分(見附圖二),由紅綠按鈕開關和1只電接點壓力表所組成,
綠色按鈕為啟動開關,紅色按鈕為停止開關,電接點壓力表用于控制供壓系統的壓力保持在你需要的范圍,當壓力指針達到上*,水泵停止工作,由于試件滲透等原因,致使水壓下降,指針逆時針轉動,離開上限位置,直至到達下限位,水泵重新啟動,水壓上升到上限位(2)控制閥。其開啟與關閉與一般閥們相同,即順時針轉為關系,逆時針旋轉為開啟,每個閥相對應控制一個試模,
HP-4.0型數顯砼抗?jié)B儀電器控制部分:由組合開關和1只壓力傳感器相連接的控制器所組成。組合開關控制抗?jié)B儀電源,“0”位為關“1”位為開;控制器用語控制供壓系統的壓力保持在你需要的范圍。關于控制器的操作說明詳見附錄《數顯抗?jié)B儀壓力控制器操作說明》
四、安裝及使用
1、準備
a、將抗?jié)B儀器放置在平整、堅實的室內基礎上,
b、關閉位于箱體右下方的放水卸壓閥
c、開啟6個控制閥
d、初次使用,注水入箱,開啟控制閥,啟動電源,至6個模座內水溢出為止,以便排出系統內空氣。
e、關閉控制閥
2、試件制作及安裝
a、試件成形養護,根據設計所要求的材料配比用成形模(亦稱副模)制作成形,然后按部或標準的規范進行掩護。
b、將養護好的試件表面晾干,然后在其側面涂山熔化的密封材料(火漆或密封蠟)注意試件兩端面,嚴禁涂有密封材料。
c、將試模加熱到40℃,然后將涂有密封材料的試件裝入模腔,再在壓機上(螺旋壓力機或借用實驗室的壓力實驗機)將試件壓入試模中并冷卻至常溫,使用本廠配套生產的HT-200型多功能脫模機,既可裝、脫模、又可劈裂試件,觀察
滲水深度。
d、將裝壓好試件的試模安裝在抗?jié)B儀的工作臺上,并均勻的擰緊螺絲帽
3、接通電源,紅色信號燈兩,將電接點壓力表上限指針調至0.1MPA 下限指針與之可靠近但不能同時接觸(約小于上限指針0.05mpa),然后摁綠鈕啟動電源,此時水泵開始工作,電接點壓力表指針隨水壓上升而順時針轉動,注意觀察壓力上升是否正常,系統有無滲漏水現象,如有異常則應排除后才能進入試驗。
4、開啟控制閥,即向相應的試體送入水壓,注意觀察試模底部有無滲出,如有滲出則需擰緊相應部位的壓緊螺帽。
5、進入正常試驗后,每隔8小時增加工作壓力0.1MPA,隨時觀察試件端面有無滲水情況,如有滲水,則關閉相應的控制閥。
6、當6個試件中有3個試件的端面有壓力水滲出時,即可停止試驗,記下十時毫的水壓作為計算依據。
7、試驗結束,切斷電源,打開放水卸壓閥,使系統壓力降至零,取下試模,
8、從試模中壓出試件,并清洗試模、模座、涂上防銹油,以備再用
五、結果計算
1、混凝土抗?jié)B標號以每組六個試件中四個未出現透水時的zui大水壓表示,其計算式為:S=10H-1其中:S-抗?jié)B標號H-六個試件中第三個滲水時的壓力(MPA)
2、如壓力加至1.2MPA經過8小時,滲水仍不超過2個,混凝土抗?jié)B標號應大于或等于12,即S=12
六、維護與保養
1、對工作環境的要求:周圍大氣溫度為5℃-45℃;相對溫度<80%,不長期在含腐蝕性氣體的環境中工作
2、水源應清潔無雜質
3、動力箱油在出廠時已加好,以后每半年打開后箱蓋及動力箱蓋,以更換一次20號或30號機械潤滑油,油量以加到接近主軸中心縣為準(約600ml)
4、每半年檢查一次動力箱底部有無積水(此項工作可在換油時同時進行),并判明是否水泵密封圈損壞,如損壞則需要更換。
5、如環境溫度低于0℃,則需放水,卸壓閥放空內的全部水源,一面結冰損壞系統的零件。
七、故障排除
以下解決方法應在排除管道、泵、閥各借口處滲漏情況后實施
1、系統壓力起步時間較長,可判斷管道內有空氣,參照出次使用排出空氣
2、系統沒有壓力,一般為水泵內密封圈磨損造成密封不嚴,更換
HBY-35型砼標準養護箱 | |||
BYS-Ⅱ標養室自動控制儀 本儀器適用于建筑、公路科研質檢及施工工地對水泥、砼試件標準養護,具有操作方便,溫濕度自控?cái)?shù)顯等優點,由大型負離子加濕器噴霧,不銹鋼水箱加熱。 主要技術參數: 1、 控溫范圍精度:0-50℃ 精度:20±2℃ 2、 控濕范圍:≥90% 加熱功率:3Kw 3、 制冷功率:1-4千大卡(選窗機) 4、 zui大溫濕控面積:15M2 5、 電壓:220V±10% | |||
HS-4型混凝土抗?jié)B儀 本儀器適用于混凝土抗?jié)B性能的試驗的抗?jié)B標號的測定,同時可用于其它建筑材料透氣測定和質量檢測。主模采用優質鋼,臺面采用不銹鋼板。 主要技術參數: 1、抗?jié)B儀zui大壓力:5Mpa 2、水泵柱塞直徑12,行程10(mm) 3、工作方式:電動手動兩用 4、外型尺寸:1100×900×600mm | |||
HCZT-1型程控磁盤振動臺 本儀器實驗室內震實成型混凝土試件及制品之用。 主要技術參數: | |||
ZH.DG—80型混凝土磁力振動臺 主要用于試驗室內混凝土抗壓試塊振實成型。 主要技術參數: (1) 臺面尺寸:800X600mm (1) 振幅(全幅):0.5mm (2) 振動頻率:50HZ (3) 每次成型試件數量:1503,試模6個1003,三聯試模3條 (4) 凈重:約240kg | |||
SjD—60型強制式單臥軸混凝土攪拌機 本機適用于建筑科研不口建筑公司及混凝土構件單位試驗室,可攪拌普通 混凝土和輕質混凝土,也可用到其它行業試驗室對不同物料進行攪拌。 主要技術參數: (1) 進料容量:96升 (2) 出料容量:60升 (3) zui大出料容量:66升 (4) 攪拌均勻時間:≤45秒 (5) 攪拌軸轉速:45轉/分 (6) 電動機功率:2.2千瓦 (7) 電源電壓:380伏 (8) 外形尺寸:1520X 530X1060mm | |||
UJZ-15型砂漿攪拌機 用于建筑工程、大專院校、科研質檢部門等作墻體粉面材料及磚砌墻用砂漿強度試驗的攪拌機,也適用于人造大理石廠家面料及其它粉末狀材料的作業。 主要技術參數: 1、攪拌葉轉速(順時)80±4r/min 2、攪拌筒轉速(逆時)60±2r/min 3、攪拌筒容量:15L 4、 攪拌筒內徑:380x250mm | |||
HVC-1型混凝土拌合物維勃稠度儀 本儀器是測定砼拌合物的維勃稠度值。用于評定混凝土拌合物坍落度在10mm內的混凝土,骨料zui大粒徑40mm。符合GBJ80-85的國家標準。 主要技術參數: 震動頻率:50±3Hz 電機:0.25千瓦380V 空載振幅:0.5±0.1m | |||
HJ-84型混凝土快速養護箱 本儀器適用于施工現場,預制構件科研等單位作混凝土快速養護,它可通過不同加速養護法預測出7天、28天令期砼抗壓,抗折強度,是砼質量控制*的設備。 主要技術參數: 1、箱內尺寸:800×580×400mm 2、工作壓力:380V 3、電熱功率:單組3Kw 計3×3Kw 4、控溫范圍:10-100℃ 5、可放試模:150×150 2組 100×100 3組 | |||
HC-7L砼含氣量測定儀 本儀器適用于集料粒徑不大于40mm,含氣量不大于10%有塌落度的混凝土拌和物中的含氣量,符合交通部發布94-07-05<公路工程水泥混凝土試驗規程>(JTJ053-94)的全部規定,該測定方法符合GBJ80-85標準。 |
瀝青試驗儀器 土工路面試驗儀器 混凝土 水泥儀器 防水卷材試驗儀器 工程塑料試模產品有:養護箱, 標養箱, 混凝土滲透儀, 混凝土鉆孔取芯機, 混凝土自落式攪拌機, 水泥電動抗折試驗機, 行星式水泥膠砂攪拌機, 產品廣泛應用于大專院校、公路鐵路、橋梁隧道、石油化工、水利建設、國防等領域。在生產銷售自主產品的同時,我廠與國內外各名優廠家一直保持著良好的協作關系,代理銷售其品牌產品,價格比廠價更優惠,我們能讓廣大客戶朋友以低廉的價格使用到更優質的產品 主營產品:混凝土標準養護箱 | 水泥標準養護箱 | 混凝土抗?jié)B儀|混凝土鉆孔取芯機 水泥凈漿攪拌機|水泥膠砂攪拌機 河北鼎盛路達實驗儀器設備廠 同時供應瀝青試驗儀器 土工路面試驗儀器 混凝土 水泥儀器 防水卷材試驗儀器 工程塑料試模,并為你組建各種實驗室。商砼攪拌站試驗儀器--商砼攪拌站混凝土試驗儀器
電 話:
傳 真:
手 機:
:張
郵 箱:dingshengludayiqi
網 址:http://www.dsldyq.com/ http://m.whqbm.com/
http://www.chem17.com/st230850
地 址:河北獻縣南河頭工業開發區18號
Concrete impervious instrument/concrete impervious instrument operation procedures/automatic regulating concrete impervious instrument
HP - 4.0 concrete impervious instrument
A, applicable scope
Concrete, is now widely used in the construction of artificial stone, for some construction, such as hydraulic construction, underwater, water, underground and other architectural engineering, building requirements has special performance - anti-permeability so-called anti-permeability is refers to the structure of material in use can resist water and/or other liquid (light oil, heavy oil) of the medium pressure infiltration under the action of performance.
HP - 4.0 type impervious instrument is mainly used in lake screw soil anti-permeability and is test and anti-permeability label measurement. At the same time can also be used for building material permeability measurement and quality inspection, so to get the relevant production, construction, the design, the research of various departments such as widely used.
Second, the main technical parameters
1, the maximum working pressure: 4 mpa
2, working ways: automatic constant pressure (digital display type: automatic constant pressure and automatic booster)
3, a can make specimen number: six
4, try die geometry (also called Lord die)
Die cavity flowing diameter: φ 174.8 mm
The mouth cavity diameter: phi 185 mm
Height: 153 mm
5, plunger pump parameters:
Flow: 0.16 L/min
6, motor:
Power: 120 w
Power supply: 380 v - 50 hz
7, physical size: 950 x 800 x 950 mm
8, quality: ≈ 220 kg
Three, the main working principle and its agencies (sees attached figure 1)
HP - 4.0 type impervious instrument is to use airtight container internal pressure is equal principle (waterhead negligence except), with water pump to the whole system to lose pressure, and through the electric contact pressure gauge and pressure controller pressure of the size of the pressure to achieve pressure water from down to up penetration pressed in the mold of the specimen, so as to test specimen anti-permeability and calculate its anti-permeability label of the instrument. HP - 4.0 type concrete impervious instrument is mainly composed of housing, table, the stainless steel panel is made, and install a six mold base and 36 M12 bolt, used for installation of mold.
For pressure system, by the motor, power box, water pump, water bag, relief valve, pipe and other components, motor used to the system to provide the power supply, power box used to motor provides power supply into a back and forth movement of the power supply and water pump, pump to the whole system to provide water, water for bag to stabilize supply system of hydraulic pressure, and the water source, power box used to motor provides power supply into a back and forth movement of the power and supply water pressure, and the water source of the shunt effect; The relief valve installation word water bag central, the role of the safety valve is to ensure that the system pressure is not more than 4 mpa4, work station, mainly by the electric control and control valve composition.
HP - 4.0 type concrete impervious instrument electric control section (sees attached figure 2), the red green button switch and one electric contact pressure gauge composed,
Green button to start switch, red button to stop switch, electric contact pressure gauge used to control system for pressure the pressure to remain in you need range and, when the pressure pointer to the limit, pump stop work, because specimen penetration and other reasons, the hydraulic pressure drop, pointer anti-clockwise rotation, leave the upper limit position, until the lower reach, a water pump restart, hydraulic pressure rise to cap a (2) control valve. The open and closed and general valve are the same, namely clockwise to relationship, anti-clockwise rotation for open, each valve corresponding control a try die,
HP - 4.0 type digital display concrete impervious instrument electric controlling part: the combination switch and one pressure sensor connection of the controller. Combination switch control impervious instrument source, "0" position close "1" for the open position; Controller term control for pressure system pressure to remain in the scope of you need. About the operation of the controller that see appendix "digital display anti-permeability meter pressure controller operation instructions"
Four, installation and use
1, ready to
A, will anti-permeability instruments on the level off, solid indoor basis,
B, closing is located in the lower right of the water pressure relief valve
C, open six control valve
D, first use, water injection into the box and open the valve, starting power supply, and 6 mold base internal water overflow so far, in order to discharge the air inside the system.
E, close control valve
2, sample production and installation
A, specimen forming curing, according to the design requirements of the ratio of materials with mold (also called vice die) making forming, and then press department or the international standard for cover.
B, and curing good specimen surface dried, then in its side TuShan melting sealing materials (sealing wax or sealing wax) note specimen two face, forbidden coated with sealing material.
C, will try to die heating to 40 ℃, then coated with seal material specimen into cavity, and then in the press (screw press or borrow laboratory pressure testing machine) will test pressure into the test mould and cooling to room temperature, it is best to use the factory supporting the production of HT - 200 type multifunction stripper, already but outfit, release, and splitting specimen, observation
Water penetration depth.
D, will put pressure good specimen trial die installed in impervious instrument work on stage, and even tighten the screw nut
3, switch on the power, the red light two, the electric contact pressure gauge cap pointer adjustment to 0.1 MPA floor pointer and the reliable near but not at the same time contact (about 0.05 MPA is less than the limit pointer), and then press the green button to start power supply, the water pump to work, electric contact pressure gauge pointer with hydraulic pressure rise and clockwise rotation, attention to the observation of pressure rise is normal or not, the system for permeability